FAQ: HOW TO FLASH / REPAIR / UNLOCK NOKIA MOBILE PHONES

Please contact nokiaguru@ucables.com if you are interested to translate in your local language.

History:

version 2.00: 26th January, 2001

Created new FAQ about How to flash / unlock /repair new nokia sw.

version 2.01: 31th January, 2001

1. Updated Troubleshootings area
2. Some corrected errors.

version 2.02: 4th February, 2001

1. New uCables Flasher Shell, it run under MSDOS is more fast and easy to use, it easily upgradeable to support new sw version.
2. New partial flash files for Nokia 3310 sw version 4.18 and 8210 sw version 5.26

version 2.03: 10th February, 2001

1. New uCables Flasher Shell version 1.2
2. Support for 6 different flash types, and 2 boot loaders
3. Full and partial flashing modes
4. New partial flash files for Nokia 7110 sw version 5.01 and 6210 sw version 4.27 and 3.74

version 2.04: 24th February, 2001

How to use Dejan Flasher directly without any nokia flasher shell (For advanced users only)
Added picture about how to connect a 3210 connector of nokia flasher cable to Troubleshooting

version 2.05: 8th April, 2001

Green nokia flasher shell, a new user friendly nokia flasher shell
Nokia MCU SW & PPM Flasher v1.03 by Dejan Kaljevic

version 2.06: 9th April, 2001

New program All nokia unlocker by Jethro version 3.11 (2.95 doesn't work)
Modification for nokia flasher cable to use with All nokia unlocker by Jethro.

Introduction
Requirements
Steps to programming a partiall flash file using a NK-FLASH cable

1. Nokia Flasher Shell and Nokia Flasher installation
2. Check sw version of nokia mobile phone
3. Run Nokia Flasher Shell
   1. MSDOS Flasher Shell 1.0 by Shulo and Man0n
   2. Windows Flasher Shell
4. Nokia Flasher 1.0b. Select nokia phone model and start address
   

Start addresses to use with partial flashing
Start addresses and files to use with FULL flashing
How works Dejan Flasher 1.00b

All Nokia Unlocker by Jethro version 3.11
New NK-FLASH2 to use with All nokia Unlocker
Green nokia flasher shell, a new user friendly nokia flasher shell
Nokia MCU SW & PPM Flasher v1.03 by Dejan Kaljevic

TroubleShootings

Finally our camarade Dejan has designed a new low cost device which can flash nokia mobile phones, now you don't need to spend 20.000 US $ in a TDF-4 box. The nokia flasher use is not dificult to use but you must be attent at every step you do. Once time you make fisrts time it will be a children game, you can flash any nokia phone in just 7 seconds.

There is two ways to flash with Dejan Nokia Flasher, Full or partially.

1. Partial Flash: is used to unlock and always should be used the same sw version file as you have in your mobile phone. This files have 64 Kb. This process take just 7 seconds.

2. Full flash: is used to unlock, repair broken phones or change phone language. Flash memory is fully changed with this procedure, EEPROM should be programmed too, but sometimes is suficient just only programming flash memory, if mobile phone not have coverage later you have flashed you must program EEPROM too, flash and eeprom files must have same sw version and language. To write or program EEPROM memory is necesary an SMD EEPROM programmer with SOIC clips (available at ucables.com from February, 2001). Flashing process can take between 1 and 3 minutes. Size of flashing files are between 500 and 1400Kb. The difference to make a full flash or make a partial flash is to used different flash files and range of addresses.If you don't need to change language, we recommend you use a partial flashing. If you really need full flashing, the best way to do it is to get another unlocked mobile phone of the same version and read flash in the appropiate address range and read eeprom. Later you must write flash and EEPROM to the phone that you want to make full flashing. New nokia models 3310, 8210 and 6210 is not necessary to reprogram EEPROM because EEPROM memoria not exist, it's stored at the FLASH.

When you make a flash you must take in mind 4 parameters, mobile phone model, phone software version (sw), flash memory type (INTEL, ATMEL, INTEL 28F160) and start address where to start to flash. First thing you must do is select the type of memory, you can choose INTEL, but if you try and it not works you can try the with ATMEL or INTEL 28F160.

To make this process easier we will explain how to flash using a Nokia flasher shell 1.5, it's a program that interface with the original MSDOS program Nokia Flasher 1.0b and it allow to select, flash type and sw version. Nokia flasher shell will show us appropiate start addresses that we must enter at nokia flasher.

Requirements:

1. NK-FLASH cable, available at http://ucables.com
2. SMD EEPROM programmercon with SOIC clips (required for full flashing only)
3. Nokia Flasher Shell + Nokia Flash 1.0b by Dejan
4. Partial flash files (included)
   
   

Steps to programming a partial flash file using a NK-FLASH cable

1. Nokia Flasher Shell and Nokia Flasher installation

a) Download new ucables_flasher_shell_12.zip
b) Unzip in the root directory c:\

The file ucables_flasher_shell_12.zip contains new ucables.com flasher shell, Nokia flasher 1.0b by Dejan, partiall flash files (.fls), and all .tia and required configuration files. If you need full flash files to repair or change languages you can find here.
Anyway you can always read full flash from an unlocked phone and dump it at the phone that you want to repair. Be sure that have same software versions, if you don't use the same software version checksums are differents and it will not work, take care you can damage your mobile phone!, at the moment we are procedure to flash with different mobile phone versions, if you don't matter to crash any phone, you can try to do this and later use Wintesla with appropiate libraries to fix coverage.

2. Check sw version of nokia mobile phone

You can read sw version pressing *#0000# (phone must be turned on and with a simcard inside), or you can read it using Nokia tool with the cable NK-567

3. Execute uCables Nokia Flasher Shell under MSDOS
We have make a new fast and easy to use flasher shell for Nokia flasher, it's easily upgradeable to support new sw nokia versions. If you have got new .fls flash files you only must copy to the c:\nk_files\partial directory and write .txt with start address. By example when we have added new file 3310-418.fls we have created 3310-418.txt writing the start flash address 280000.

a) If you a have windows run a msdos box, From Windows Press Start menu, select Run, write cmd and press enter.
b) Go to flasher directory and run flash.com program with appropiate parameters.

Command line options:
FLASH <nokia model> <flash type> [sw version] [flashing mode] [boot type]

Parameters:
Nokia models
3210, 3310, 5110, 6110, 6150, 6210, 7110, 8210 and 8850

Flash type:

1 = INTELW 8	2 = AMD 8	3 = INTEL 16
4 = INTELW 16	5 = ATMEL 16	6 = ST 32

sw version (optional): XXX
by ex. if your nokia 3210 sw version is 5.31, with an INTELW 8, to make
a partial flash you must write: flash 3210 1 531

Flashing mode (optional):
1 = Partial flash (write down initial start flash address)
2 = Full flash (write down initial start and final flash address)

Boot type (optional):
1 = Boot type 1
2 = Boot type 2

c) Select sw version that have your nokia phone (it's the sw number that you get in the step 1 with Nokia tool). It's very important that you use the same sw version, or you can damage your mobile phone. Below you can check an example using a Nokia 3310 sw version 4.18 with INTEL flash type

C:\>cd flasher C:\flasher>flash 3310 1 418 MSDOS Shell for Dejan Nokia Flasher v 1.2 by Shulo and Man0n uCables International. http://ucables.com Find instructions at: http://gsmsearch.com/faq/nokiaflasher.html Nokia 3310 Flash type: intelw_8 sw version: 418 Partial flash mode start flash address: 280000 write it when Nokia Flasher ask for initial flash address. http://ucables.com boot type: 1 Flasher has been configured with appropiate files to partial flash write down start address and final address (only full flash) that you must specify to Dejan Flasher. Strike any key when ready...

Write down the start flash address, because you will need when Nokia flasher request it.

Nokia flasher shell will launch Nokia Flasher 1.2 under MSDOS with the parameters that we have selected.

4. Nokia Flasher 1.0b. Select nokia phone model and start address

Press F2	Press Enter to select nokia model
Press Enter to select flash file and enter start address that you have write previously (be sure that you write the right start address or you can crash your phone)	Press Enter and turn on your mobile phone inmediately (Some nokia models not require to turn on like 3210).
If you get a screen error the problem, probably you have an incorrect computer configuration (not use notebooks), or you have choose incorrectly the flash memory type.
	If you finally you have successfully write your flash your mobile phone will be free!!! ;)

Start addresses to use with partial flashing. Partial flash files .fls are included at the installation directory of nokia flasher.

Start addresses and files to use with FULL flashing.

Green nokia flasher shell, a new user friendly nokia flasher shell

There is a new flasher shell it green nokia flasher shell that have a userfriendly interface and you can add easily new flash versions. Download here

Nokia MCU SW & PPM Flasher v1.03 by Dejan Kaljevic

Nokia MCU SW & PPM Flasher v1.03 by Dejan Kaljevic is public domain but still have not been fully cracked. Anyway you can download from here. If you have problems to download it, go to: http://ucables.com/members/download (only ucables members)

This software is useful only for changing MCU software and PPM package.

MCU SW
MCU SW is main software with all needed functions for proper work of phone.
MCU SW from one type (like 5110) you CAN'T use on other
phone type (like 6110).
Changing MCU SW is useful only if you wish to UPGRADE current
software with new one that have fixed bugs or added some new functions.
Also you can overwrite MCU SW with same version if you have bad
data in FLASH where is MCU SW stored.

PPM Data
PPM Data are block of data that define different groups of users,
like language groups.
Nokia made this format of data because of FLASH size limit.
Since there is lots of languages and fonts over the world,
in one PPM file can be from 1- approximately 20 languages.
Changing language is a main reason of changing PPM data.
Also you can overwrite PPM package with same version if you have bad
data in FLASH where is PPM data stored.

You can find more info about this new release at Dejan website: http://www.net.yu/~dejan/flasher/flasher.html

All Nokia Unlocker by Jethro version 3.11

No more dead nokia phones! use new cable NK-FLASH2 with new All nokia unlocker 2.95 by Jethro and you dont need flash anymore. Only need to push 2 buttons to unlock new nokia phones, version 2.95 unlock the following versions:

• Nokia 3210: V05.31, V05.36, V06.00
• Nokia 3310: V03.24, V04.02, V04.06,V04.18,V04.23
• Nokia 5110: V05.28, V05.29, V05.30
• Nokia 5130: V05.71
• Nokia 6150: C5.22, V5.23
• Nokia 6210: V03.01, V03.04, V04.08, V4.27
• Nokia 7110: V04.88, V04.94, V05.00, V5.01
• Nokia 8210: V5.11, V5.16, V5.20, V5.21, V5.25. V5.26
• Nokia 8850: V5.11,V5.16, V5.20, V5.21, V5.25, V5.26

New NK-FLASH2 to use with All nokia Unlocker

The unique difference between NK-FLASH (original dejan box) and NK-FLASH2 is to have PIN 7 and PIN 12 solded at the Paralel connector to be compatible with All Nokia Unlocker 3.11 by Jethro You don't need to flash, this program will do for you all automatically, unlocking without any risk. Of course this cable is 100% compatible with Dejan Flasher and all shells. Please be sure that you use version 3.11 because other version like 2.95 will not works. If you have problems to download it try http://ucables.com/members/download (only members)

If you already got a NK-FLASH from ucables.com you can modify easily, to locate PIN 7 and PIN 12 at NK-FLASH you must take off housing to the parallel connector and if you look from the top (at the I.C. side) with the connector side down you can start to count from left to right. You can see the numbered PINS if you see the parallel connector in front view of the cable NK-FLASH2

1. I Have selected the right flash type and start address but Nokia flash give me error: BOOT TX data error
a) Try different flash types from 1 to 6. You must try TO READ pressing F1 from Dejan flasher to check connection is working.
b) Don't use Nokia Flasher in a notebook, Paralel port not works not works like in computer desk.
c) Configure BIOS Paralel port with different modes EPP or SPP, etc. SPP should works.
d) Try in another computer may be configuration is not good

2. I need to partial flash new nokia mobile phones sw version like Nokia 7110 version 5.XX, where can i get new partial files for this phones and initial flash addresses?
Please be patient, we are working hard collecting and checking new partial flash files, our faq will be updated often and you will find new partial files here every month. Anyway you can try to read partial flash using same range addresses as in the previous version and try if it works, but you must do that making a full flash backup copy of your nokia phone. Once time you have done full backup you can try to read 3A0000 to 3AFFFF and write it to your nokia 7110, if not works you must restore your full flash backup and try again with a new range by example from 3B0000 to 3BFFFF.

3. I can't to connect my 3210 nokia flasher connector to my phone. What must i do?
The 3210 connector uses 6 pins, so it's wider and it's not easy to connect, but see this picture to know how you must connect it.

Before to start to flash you nokia phone it's you must make a backup of your nokia phone reading the full flash or your nokia phone from appropiate flash addresses that you can check at our list depend on your nokia sw version

If you have an unlocked new version 100% working of nokia not included at our list. Please contact by email with nokiaguru@ucables.com and we will tell you appropiate start and end address.

(c) 2001. Spain. nokiaguru